### GATE ME 2010 Paper | GATE Mechanical Engineer (ME) Paper 2010 | GATE 2010 ME Solved Paper

1. Which of the following statements is INCORRECT?
(A) Grashof’s rule states that for a planar crank-rocker four bar mechanism, the
sum of the shortest and longest link lengths cannot be less than the sum of
(B) Inversions of a mechanism are created by fixing different links one at a time.
(C) Geneva mechanism is an intermittent motion device
(D) Gruebler’s criterion assumes mobility of a planar mechanism to be one

2. Tooth interference in an external involute spur gear pair can be reduced by
(A) decreasing center distance between gear pair
(B) decreasing module
(C) decreasing pressure angle
(D) increasing number of gear teeth
3. For the stability of a floating body, under the influence of gravity alone, which of the following is TRUE?
(A) Metacentre should be below centre of gravity
(B) Metacentre should be above centre of gravity
(C) Metacentre and centre of gravity must lie on the same horizontal line
(D) Metacentre and centre of gravity must lie on the same vertical line
4. The maximum velocity of a one-dimensional incompressible fully developed viscous flow, between two fixed parallel plates, is 6ms-1. The mean velocity (in ms-1) of the flow is
(A) 2 (B) 3 (C) 4 (D) 5
5. A phenomenon is modeled using n dimensional variables with k primary dimensions. The number of non-dimensional variables is
(A) k (B) n (C) n-k (D) n+k
www.way2fresher

6.One kilogram of water at room temperature is brought into contact with a high temperature thermal reservoir. The entropy change of the universe is

(A) equal to entropy change of the reservoir
(B) equal to entropy change of water
(C) equal to zero
(D) always positive
7. A hydraulic turbine develops 1000kW power for a head of 40m. If the head is reduced to 20m, the power developed (in kW) is
(A) 177 (B) 354 (C) 500 (D) 707
8. The material property which depends only on the basic crystal structure is
(A) fatigue strength (B) work hardening
(C) fracture strength (D) elastic constant
9. In a gating system, the ratio 1:2:4 represents
(A) sprue base area: runner area: ingate area
(B) pouring basin area: ingate area: runner area
(C) sprue base area: ingate area: casting area
(D) runner area: ingate area: casting area

1. sony v s says:

i want banglore university 3 year llb question papers

2. SURESH.P says:

One member how many time to write gate exam. (sc student)

• Ajai S says:

No limit for gate exams

3. hoda says:

plz send solution of gate question of 2009 & 2010.
Any change in patern of GATE of 2011?

4. NEERAJA says:

plz send mech engg (2000-2010) gate exam papers

5. godage gahininath says:

i want solved question paper of gate

6. AMIT PAWAR says:

I want last 10 years solved question papers of mechanical engg.

7. kishore says:

how to change a gate center in btwen diff zones

8. ashok says:

how to get gate sloved papers.
plz tell me

9. vijay says:

sir i want gate metrial for mechanical eng

10. vijay says:

plz … send study metrial for gate mech

11. om prakash says:

good afternoon sir,plz tell me no. of question in gate 2011 paper and also send me solve paper of physics 2009 and 2010 with formule

12. pr singh says:

i want chemistry solved paper 2009 and 2010

• pr singh says:

i want gate 2009 and 2010 solved question paper of chemistry.

13. sindhu says:

this gate paper is easy compared to previous papers……….i thnk next year it might me hard