BHEL Recruitment Exam Smaple Questions | BHEL Placement Papers

BHEL Sample Placement Papers with Answers for 2008 or BHEL written pattern of Question Papers or BHEL written recruitment Papers can be checked here.

BHEL Placement Papers for 2008 :

1. The ratio of two specific heats of air is equal to. = 1.41

2. A perfect gas at 270C is heated at constant pressure till its volume is double. The final temperature is = 3270C

3. An engine operates between temperature of 9000K and T2 and another engine between T2 and 8000K. For both to do equal work, value of T2 will be. = 6500K

4. Internal energy of a substance depends on = Temperature

5. Work done in compressing 1kg of gas adiabatically from p1,V1,T1 to p2, V2, T2 is equal to = Cv(T2-T1)

6. The unit of entropy is = J/kg 0K

7. Indicated power of a 4-stroke engine is equal to = pLAN/2

8. Which of the following is not an internal combustion engine : a) 2 stroke petrol engine b)4 stroke petrol engine c) Diesel engine d) steam engine e) Gas turbine. = (d)

9. If one cylinder of a diesel engine receives more fuel than the others, then for that cylinder the: a) exhaust will be smoky b) piston rings would stick into piston grooves c) exhaust temperature will be high d) engine starts overheating e) all of the above. = (e)

10. The spark plug gap is normally maintained at: = 0.45 to 0.6mm

11. A distributor in spark ignition engines performs the function of : = Providing the correct firing order in engine

12. Which of the following does not relate to C.I. engine:: a) fuel pump b) fuel injector c) governor d) carburetor e) flywheel = (d)

13. Air fuel ratio in a jet engine is = 60:1

14. What is the value of Prandtl No.?

15. In domestic refrigerator, the tubes at the back of the refrigerator are: a) evaporator b) condenser c) capillary tubes d)………

16. Which refrigerants has the highest critical point temperature. = Freon-11

17. Wet bulb temperature is. = indication of amount of moisture in air

18. On psychrometric chart, dry bulb temperature lines are. = Vertical

19. Surface tension has the units. = newtons/m

20. The line of action of the buoyant force acts through the. = centroid of the displaced volume of fluid

21. A pressure of 25m of head of water is equal to. =245kN/m2

22. For a submerged body to be in stable equilibrium, the centre of gravity should be. =Below the centre of buoyancy.

23. The actual velocity at vena contracta for flow through an orifice from a reservoir of height H=?. =Cvv2gH

24. A body weighing 2kg in air weights 2.5kg when submerged in water. Its specific gravity is. = 6

25. In a free vortex motion: = each particle moves in a circular path with a speed varying inversely as the distance from the centre.

26. A centrifugal pump has speed-1000rpm, Flow-1200l.p.m, Head-20m, Power-5H.P. If its speed is increased to 1500rpm, new flow will be.: = 1800l.p.m

27. Runaway speed of a hydraulic turbine is: = the speed if the turbine runner is allowed to revolve freely without load and with the wicket gates wide open.

28. 10m of water column is equal to = 100kN/m2

29. M.I. of a circular area about an axis perpendicular to the area is: = pr4/2

30. A projectile is fired at an angle ? to the vertical. Its horizontal range will be maximum when ? is . =450

31. An elevator weighing 1000kg attains an upward velocity of 4m/sec in two seconds with uniform acceleration. The tension in the supporting cables will be = 1200kg.

32. A 13m ladder is placed against a smooth vertical wall with its lower end 5m from the wall. What should be the co-efficient of friction between ladder and floor so that it remains in equilibrium. = 0.21

33. A car is moving with a velocity of 60km/hr and possesses energy of 5×105 joules. The mass of the car will be. =3000kg.

34. If l is the span of a light suspension bridge whose each cable carries total weight (w) and the central diop is y, the horizontal pull at each support is: = wl/y OR

35. A beam of length l, having uniform load w kg/unit length is supported freely at the ends. The moments at mid span will be: = wl2/8.

36. A boiler shell 200cm dia and plate thickness 1.5cm is subjected to internal pressure of 1.5MN/m2, then the hoop stress will be. = 100N/m2

37. 100KW is to be transmitted by each of two separate shafts. A is turning at 250rpm and B at 300rpm. Which shaft must have greater diameter.: = B

38. Two identical leaf springs of spring constant k are arranged like cantilevers in parallel and attached at free end by a spring of spring constant k. The equivalent spring constant of combination is; = 1.5k.

39. Automobile steering gear is an example of: = lower pair.

40. The type of coupling used to join two shafts whose axes are neither in same straight line nor parallel, but intersect is. = Universal coupling.

41. To transmit power from one rotation shaft to another whose axes are neither parallel nor intersecting, use: = Spiral gear.

42. A gear having 100 teeth is fixed and another gear having 25 teeth revolves around it, the centre lines of both gears being joined by an arm. How many revolutions will be made by gear of 25 teeth for one revolution of arm. = 5 rev.

43. The secondary critical speed of a shaft occurs at: = twice the speed of primary critical speed.

44. Brittle coating technique is used for: = experimental stress analysis.

45. Factor of safety is the ratio of: = yield stress/working stress.

46. Type of gear used for non-intersection perpendicular shafts: = Hypoid gears.

47. Corrosion resistance of steel is increased by adding: = Chromium & Nickel

48. The product of Cupola is called: = cast iron

49. Brinell tester uses a hardness steel ball of size: = 10mm

50. Sintered and tungsten carbides can be machined by: = EDM

51. What kind of abrasive cut off wheel should be used to cut concrete, stone and masonry? =Diamond grit.

52. In break-even analysis, total cost consists of: = Fixed cost + Variable cost.

53. The amount deducted from the salary of workers towards employees provident fund is : =deposited in the account of worker with Provident Fund Commissioner.

54. PERT is: = event oriented technique

55. Bar charts are suitable for: = minor works.

56. ? on a PERT/CPM chart represents: = a significant event representing some mile-stone

57. Electron volt is the unit of : = Energy.

58. Seamless tubes are made by?

59. Reheating in gas turbine results in: = increase of work ratio and decrease of thermal efficiency.

60. Why DC current is not used in transformer?

61. What is the purpose of draft tube in hydraulic turbines: = to convert the kinetic energy into pressure energy.

62. A mass of 100kg is falling from a height of 1m and penetrates the sand to 1m. what is the resistance force of the sand?

63. Two cars travel in the same direction at 40km/hr at a regular distance. A car comes in the opposite direction at 60km/hr. It meets each car in a gap of 8 seconds. What is the distance between the two cars?

If you have questions, please ask below

153 Comments


  1. Please send bhel artisans question papers in electrician trade says:

    Plz send bhel artisan question paper electriciae trade

  2. vijaykumar.j says:

    i want electronics mechanic module question papper in bangalore

  3. akhilesh says:

    hello sir , plz send me the syllabus for recruitment of artisen.(fiter)

  4. mohan says:

    please send me sample question papers for BHEL ITI exams its very urgent plz send it to my mail id…

  5. virendra kumar rai says:

    please send me the artisian sample paper of electrician trade.

  6. murarianil says:

    sir pls send to me bhel artisan fitter previous qustion papers sent to my email id sir

  7. durgesh kumar says:

    please sir sent me the model question paper for bhel artisan exam. fitter

  8. arun says:

    hello sir can i get previous batch sloved question paper of artisan, it will help me for preparing the interview.

  9. SURENDRA says:

    hi sir please send me any bhel artisan previus papers for fitter

  10. m.shajahan says:

    dear sir,i want ITI ELECTRNICS MECH model question paper plz send my email id.

  11. chethan H.M says:

    please sent me bhel electronics sample papers please sir.

  12. basu says:

    please sir send me bhel fitter all question paper with answer

  13. kasif ahmed says:

    respected sir i want to appear in fitter trade written exam so sir i dont have idea about the exam pattern so plzkidly suggest me what to do waiting for your suggestion thank u..

  14. vijay says:

    hai sir i whant bhel previus FITTER qustion papers plz send me my E MAIL: wijaykumaran@yahoo.co.in

  15. shoan says:

    good mornng sir i am donig apprentice in bhel so i plz requst send the model papers of fitter. plzzzzzzzzzzzzzzzzz.

  16. shoan says:

    good mornng sir, i am donig apprentice in bhel. plz send exam model papers

  17. geethika says:

    sir,please send me previous(5 years)bhel recruitment papers(electronics stream)to mail geethika.shar415@gmail.com

  18. gyanendra says:

    pl send me model question papers for trade of blacksmith and turner.

  19. pavana says:

    sir, please send me the privious year bhel recruitment papers(electronics stream) for probationary engineer post to mail pavana_22@yahoo.com

  20. B.vinothkumar says:

    respected sir, please send me ITI(MMV)crane operator artison bhel model question paper to this mail id. thanking you. vino.emech@gmail.com

  21. Umesh Jamkhande. says:

    please send me questions which is related to FITTER Trade.

  22. JAMES says:

    sir,please send me artisan ITI mechanic model qustion paper my emil id.

  23. KUNAL ROY says:

    respected sir ,please send me ITI fitter artison bhel model question paper to this maill ID. thank u

  24. nagarajan.c says:

    respected sir, please send me iti electrical artison bhel question paper to this mail id.thank u

  25. P.SHRAVAN KUMAR says:

    Sir please send interview questions for ITI-FITTER

  26. R.ARULRAJ says:

    Dear sir,pls send ITI FITTER ARTISION MODEL QUS AND ANS.YEARS 2008-2011 TO MY EMAIL ID. PLS PLS HELP ME SIR. THANK U.

  27. madhavan t says:

    respected sir,please sent me iti fitter artisan bhel model questions paper kinly to this mail id. thanking you sir………..

  28. saravanan says:

    hai sir,please send me the artisian sample question paper of GRINDER trade

  29. saravanan says:

    sir,plz send me the artisian sample paperof MACHINIST trade

  30. saravanan says:

    sir,please send me artisan sample question paper of GRINDER trade

  31. Rajneesh neware says:

    respected sir ,please send me ITI fitter artison bhel model question paper to this maill ID. Thank u sar

  32. Rajneesh neware says:

    Suprbhat, respected sir ,please send me ITI fitter artison All bhel model question paper to this maill ID. Thank u sar

  33. DAYANAND JAGTAP says:

    Respected sir,
    Please send me iti fitter NCTVT all bhel model question papers to this mail id dayanand.jagtap2@gmail.com,
    thank you sir,

  34. VISHWAS SAINI says:

    sir, kindly please send me iti fitter bhel artisian modal question paper on my mail id.

  35. ranjith says:

    i need mechanical question paper

  36. venkatraman .s says:

    sir Good evening,sent to mmv qustion paper plz sir.

  37. suresh babu m says:

    respected sir ,please send me ITI Electronic mechanic bhel model question paper to this maill ID-suresh.babu1987@yahoo.co.in

    Thank u sar

  38. Barendra sethi says:

    PLZ SEND ME BHEL PREVIOUS YEAR QUESTION PAPER FOR DIPLOMA IN CIVIL ENGG. THROUGH MY EMAIL ID

  39. Arunkumar says:

    Sir i am applying supervisory trainey job so i don’t have sc caste certificate in english i am having sc caste certificate in kannada so can i send this format

  40. Mohammed says:

    any body having BHEL-Electronics model qus paper,

  41. Ravi says:

    sir kindly send me ITI eletronic mech bhel question paper and ans on my e mail id

  42. vijay kumar says:

    sir kindly me iti fitter please question paper and my admit card nol. 9204950

  43. Bubble Spinner - Bubble Shooter - Play Bubble Shooter Games says:

    This is a good write-up. I will spend more time looking into this subject.

Leave a Reply

If you have any questions headover to our forums

You can use these XHTML tags: <a href="" title=""> <abbr title=""> <acronym title=""> <blockquote cite=""> <code> <em> <strong>